| Name | Narrow Nose Wire Pulling Forceps |
| Lead Time | 0-3 days |
| Competitor | ;LX172R;145631;14-5631;1456-31; |
| Specialty | Neuro, Ortho & Spine-Wire/Pin Cutters & Pliers |
| Material Finish | Stainless Steel |
| Grade | Premium Operating Room |
| Units of Measurement | Each |
| Manufacturer | Ophthalmic Zone |
| Sterility | Non-Sterile |
| Usage | Reusable |
Narrow Nose Wire Pulling Forceps
3mm tip, 7-1/2″ (19.1 cm)Â Narrow Nose Wire Pulling Forceps are ideally suited for use in a variety of orthopedic procedures that require the use of wire. A wide range of procedures such as fracture repair requires the use of wire to stabilize the bone fragments to accelerate the healing process. This forceps is made in an extra heavy jaw pattern that makes it ideal for pulling K-wire and Steinmann pins. This instrument features a 3.0 mm tip that allows it to fit into more difficult to access areas.
Description
Reviews (0)
Related products
Delicate Wire Cutter – Tungsten Carbide
tungsten carbide jaws, cuts up to 1/36" (0.7 mm) diameter hard wire, 4-3/4" (12.1 cm)Â Delicate Wire Cutter is a versatile instrument crafted for use in trimming and cutting lengths of wire. Procedures such as laminectomies require addition of wire to confer some stability to the vertebrae to prevent trauma as healing occurs. This particular cutter is specifically designed for use with delicate wires. It features tungsten carbide jaws and are capable of cutting hard wire up to a diameter of 0.7 mm.
Diamond Pin Wire Cutter
cuts up to 5/64" (2.0 mm) diameter hard wire, 6-1/2" (16.5 cm)Â Diamond Pin Wire Cutter is a specially designed instrument crafted for use in cutting wire. Many different neurosurgical and orthopedic procedures require the insertion of wire to give the areas additional stability and this cutter can be used to clip these at the desired length. Not only can this instrument be used to trim wire but also surgical pins. Fracture repair and other bone repair surgeries has to be set with pins that also need to be trimmed using this instrument. This instrument is available in two designs: stainless steal or tungsten carbide both of which can cup up to a diameter of 2.0 mm.
End Cutter – Double Spring, Large, Tungsten Carbide
tungsten carbide jaws, double-action, maximum capacity 3?32" (2.5mm), 8-1/2" (21.6 cm)Â End Cutter is a unique instrument designed for cutting of surgical pins or wire. Many orthopedic and neurosurgical spinal procedures require the use of such stabilization accessories to prevent trauma during recovery and confer additionally stability. This instrument is particularly well suited for end cutting which allows it to be made flush with the edge of bone or other tissue ares where it is being used. Additionally this end cutter is double-action and features tungsten carbide jaws with a maximum capacity of 3/32".
Flat Nose Pliers
serrated jaws, 5-1/2" (14.0 cm)Â Flat Nose Pliers are ideally suited for use in manipulation of wire. Particularly these pliers can be used in situations where it is required to make very sharp, angled bends in the wire. The wider tip makes this instrument ideal for grasping Steinmann pins and K-wires. Additionally this instrument measure 5.5" long and is forged from premium German grade steel making it a finely crafted and reliable instrument.
Flush Wire Cutter – Tungsten Carbide
tungsten carbide jaws, double-action, front & side cutting, cuts up to 1/16" (1.7 mm) diameter hard wire, 7" (17.8 cm)Â Flush Wire Cutter is an instrument designed for use in cutting wires during surgical procedures. A variety of procedures require the insertion of wire to stabilize an inserted graft or fracture repair. This decreases potential for trauma and increases the speed of healing. This cutter features double-action tungsten carbide jaws that allow for precise cuts on wire up to 1.7 mm diameter. This instrument can be used for both front and side cutting.
Hercules-Type Cable Cutter
replaceable tungsten carbide blades, for 1.0 mm to 2.0 mm cables, 7" (18.0 cm)Â Hercules-Type Cable Cutter can be used to trim and adjust the length of cables. This instrument features replaceable tungsten carbide blades that can be used on for cables from 1.0 mm to 2.0 mm. Tungsten carbide jaws gives this instrument added strength as it is the hardest metal made for surgical instruments and results in a supremely durable jaw that can be used for sustained cutting. Additionally this instrument is 7" long and has gold tipped handles.
Hercules-Type Wire Cutter – 2.2 mm Wire Max
for drill-wires of max 2.2 mm, replaceable tungsten carbide blades & replaceable rubber jaws, 7" (18.0 cm)Â Hercules-Type Wire Cutter is a highly reliable instrument made for use in a variety of surgical procedures that require wire and thus cutting of wire. This wire cutter is specifically designed for use with drill-wires at a maximum 2.2 mm. This instrument features replaceable tungsten carbide blades which are inherently more durable than stainless steel and have an extended service-life. It also features replaceable rubber jaws making it highly versatile and customizable to accommodate a vast array of surgical scenarios. This instrument is available in either a standard design or left-handed.
Lineman Pliers
side-cutting, maximum capacity 1.6 mm, 8-1/2" (21.6 cm)Â Lineman Pliers are a multi-purpose instrument designed for use in surgical procedures to manipulate wire. Many orthopedic surgeries such as fracture repair depend on the use of wire to approximate the fragments and accelerate the healing process. Wires must be manipulated and wrapped to fit the particular scenario where they are needed and these pliers are built for that. They features tungsten carbide jaws and are side cutting with a maximum capacity of 1.6 mm.
Reviews
There are no reviews yet.