| Name | Demel Wire Guide |
| Lead Time | Lead time advised within 48 hours of order placement. |
| Specialty | Neuro, Ortho & Spine-Wire Tighteners |
| Material Finish | Stainless Steel |
| Grade | Premium Operating Room |
| Units of Measurement | Each |
| Manufacturer | Ophthalmic Zone |
| Sterility | Non-Sterile |
| Usage | Reusable |
Demel Wire Guide
Demel Wire Guide is a specialized instrument crafted for use in surgical procedures that require the addition of wire. This instrument features a smooth handle from which extends a slim neck and a hook shaped head. Many orthopedic procedures require the use of wire for stability such as to wrap around a bone to approximate a fracture and this instrument can be used to comfortably manipulate wire. This instrument is available in three sizes 30.0 mm, 47.0 mm and 57.0 mm diameters.
Description
Reviews (0)
Related products
Diamond Pin Wire Cutter
cuts up to 5/64" (2.0 mm) diameter hard wire, 6-1/2" (16.5 cm)Â Diamond Pin Wire Cutter is a specially designed instrument crafted for use in cutting wire. Many different neurosurgical and orthopedic procedures require the insertion of wire to give the areas additional stability and this cutter can be used to clip these at the desired length. Not only can this instrument be used to trim wire but also surgical pins. Fracture repair and other bone repair surgeries has to be set with pins that also need to be trimmed using this instrument. This instrument is available in two designs: stainless steal or tungsten carbide both of which can cup up to a diameter of 2.0 mm.
End Cutter – Barrel Spring, Small, Tungsten Carbide
tungsten carbide jaws, w/ coil spring, maximum capacity 1/16" (1.7mm), 6" (15.0 cm)Â End Cutter is a unique instrument designed for cutting of surgical pins or wire. Many orthopedic and neurosurgical spinal procedures require the use of such stabilization accessories to prevent trauma during recovery and confer additionally stability. This instrument is particularly well suited for end cutting which allows it to be made flush with the edge of bone or other tissue areas where it is being used. Additionally this end cutter features tungsten carbide jaws and has a maximum capacity of 1/16".
Flat Nose Pliers
serrated jaws, 5-1/2" (14.0 cm)Â Flat Nose Pliers are ideally suited for use in manipulation of wire. Particularly these pliers can be used in situations where it is required to make very sharp, angled bends in the wire. The wider tip makes this instrument ideal for grasping Steinmann pins and K-wires. Additionally this instrument measure 5.5" long and is forged from premium German grade steel making it a finely crafted and reliable instrument.
Flush Wire Cutter – Tungsten Carbide
tungsten carbide jaws, double-action, front & side cutting, cuts up to 1/16" (1.7 mm) diameter hard wire, 7" (17.8 cm)Â Flush Wire Cutter is an instrument designed for use in cutting wires during surgical procedures. A variety of procedures require the insertion of wire to stabilize an inserted graft or fracture repair. This decreases potential for trauma and increases the speed of healing. This cutter features double-action tungsten carbide jaws that allow for precise cuts on wire up to 1.7 mm diameter. This instrument can be used for both front and side cutting.
Hercules-Type Cable Cutter
replaceable tungsten carbide blades, for 1.0 mm to 2.0 mm cables, 7" (18.0 cm)Â Hercules-Type Cable Cutter can be used to trim and adjust the length of cables. This instrument features replaceable tungsten carbide blades that can be used on for cables from 1.0 mm to 2.0 mm. Tungsten carbide jaws gives this instrument added strength as it is the hardest metal made for surgical instruments and results in a supremely durable jaw that can be used for sustained cutting. Additionally this instrument is 7" long and has gold tipped handles.
Hercules-Type Wire Cutter – 2.2 mm Wire Max
for drill-wires of max 2.2 mm, replaceable tungsten carbide blades & replaceable rubber jaws, 7" (18.0 cm)Â Hercules-Type Wire Cutter is a highly reliable instrument made for use in a variety of surgical procedures that require wire and thus cutting of wire. This wire cutter is specifically designed for use with drill-wires at a maximum 2.2 mm. This instrument features replaceable tungsten carbide blades which are inherently more durable than stainless steel and have an extended service-life. It also features replaceable rubber jaws making it highly versatile and customizable to accommodate a vast array of surgical scenarios. This instrument is available in either a standard design or left-handed.
K-Wire Side Cutter – Tungsten Carbide
tungsten carbide jaws, cuts up to 0.047" (1.1 mm) diameter hard wire, 6" (15.2 cm)Â K-Wire Side Cutter is a versatile instrument that can be used in a variety of surgical procedures. It is specifically designed for use in cutting wire in a particular perpendicular orientation. The unique design of this instrument allows it to comfortably be set flush against the areas where the wire has been inserted and clip it at a length that makes it the best fit. A variety of spinal procedures require for the placement of wire through the newly grafted area to give additional support throughout recovery and this instrument can be used in manipulation and cutting of these wires. Additionally this instrument features tungsten carbide jaws and can cut wires up to a diameter of 1.1 mm.
Kirschner Bow
Kirschner Bow is an instrument that can be used in a variety of orthopedic surgical procedures. A kirschner wire can be used to stabilize and approximate fractures after surgical repair. These wires can be quite easy to insert but must be manipulated with the proper instrumentation such as this bow. This bow applies a longitudinal force of tension that prevents rotation of the wire within the apparatus. This instrument is available in three sizes: medium, large and extra large as well as a set of 3 extra hooks for the krischner bow.
Reviews
There are no reviews yet.